Login

INFN Milano LHCb UT workshop

17–19 May 2016
INFN - Sezione di Milano
Europe/Zurich timezone

Contribution List

30 out of 30 displayed
Export to PDF
  1. 1. Introduction and goals of the workshop
    Marina Artuso (Syracuse University (US))
    17/05/2016, 14:00
  2. 3. Status of the area from the end of stave to the DCB, based on the model
    Jason Emory Andrews (University of Maryland (US))
    17/05/2016, 14:20
  3. 4. Status and plans for the pigtails
    Maria Del Pilar Peco Regales (Max-Planck-Gesellschaft (DE))
    17/05/2016, 14:40
  4. 5. Mechanics and cooling requirements for the PEPI chassis
    Thomas Ernest O'Bannon (University of Maryland (US))
    17/05/2016, 15:00
  5. 6. Discussions on PEPI assembly and repair
    Burkhard Schmidt (CERN), Thomas Ernest O'Bannon (University of Maryland (US))
    17/05/2016, 15:20
  6. 19. Discussion
    17/05/2016, 15:40
  7. 13. Issues on the Mechanics/Electronics Interface
    Ray Mountain (Syracuse University (US))
    17/05/2016, 16:30
  8. 14. Results from Cooling Measurements at Milano
    Simone Coelli (Università degli Studi e INFN Milano (IT))
    17/05/2016, 17:00
  9. 15. Tour of TRACI Cooling Test Setup (Optional)
    Simone Coelli (Università degli Studi e INFN Milano (IT))
    17/05/2016, 17:30
  10. 7. Tests of SALT8
    Jianchun Wang (Syracuse University (US))
    18/05/2016, 09:00
  11. 8. SALT Design I
    Marek Idzik (AGH University of Science and Technology (PL))
    18/05/2016, 09:20
  12. 9. SALT Design II
    Krzysztof Piotr Swientek (AGH University of Science and Technology (PL))
    18/05/2016, 09:40
  13. 29. Discussion
    18/05/2016, 10:00
  14. 25. Status of flex cable and hybrid projects
    Mauro Citterio (Università degli Studi e INFN Milano (IT))
    18/05/2016, 11:30
  15. 26. Characterisation of second generation flex cables
    Nadim Conti (INFN Milano)
    18/05/2016, 11:50
  16. 27. Plans for production and Q&A test
    Mauro Citterio (Università degli Studi e INFN Milano (IT))
    18/05/2016, 12:10
  17. 28. Discussion
    18/05/2016, 12:30
  18. 16. The UT electronics slice test goals & preparation at Syracuse
    Jianchun Wang (Syracuse University (US))
    18/05/2016, 15:00
  19. 17. COMET & interface test status
    Will Parker (University of Maryland (US))
    18/05/2016, 15:20
  20. 18. Discussion
    18/05/2016, 15:40
  21. 10. SALT design III
    Dr Tomasz Andrzej Fiutowski (AGH University of Science and Technology (PL))
    18/05/2016, 16:30
  22. 11. Preparation of SALT test setup
    Carlos Abellan Beteta (Universitaet Zuerich (CH))
    18/05/2016, 16:50
  23. 12. SALT chip testing
    Tomasz Andrzej Fiutowski (AGH University of Science and Technology (PL))
    18/05/2016, 17:10
  24. 30. Discussion
    18/05/2016, 17:30
  25. 20. General overview of schedule constraints and milestones for transition to construction & construction
    Marina Artuso (Syracuse University (US))
    19/05/2016, 09:00
  26. 21. Manpower, resources and risk analysis
    Sheldon Stone (Syracuse University (US))
    19/05/2016, 09:20
  27. 22. Communication challenges in geographically fragmented tasks (mostly electronics) and strategies to eliminate “dead times” and interface problems
    Olaf Steinkamp (Universitaet Zuerich (CH))
    19/05/2016, 09:40
  28. 24. Discussion
    19/05/2016, 10:00
  29. 23. Discussion
    19/05/2016, 11:30
  30. 2. Status of the area from the end of stave to the DCB, based on the mode
    Jason Emory Andrews (University of Maryland (US))