Commissioning schedule, MAD-NG parametric matching and Velo aperture (joint LNO-NDC)

→ Europe/Zurich
Zoom Meeting ID
66832985836
Host
Rogelio Tomas Garcia
Useful links
Join via phone
Zoom URL

Joint LNO-NDC section meeting on Commissioning schedule, MAD-NG parametric matching and Velo aperture

 

News

Stefano and Rogelio : next week has Geneva school holidays and no meeting is planned. The next section meeting is planned for the 28 February and will likely be another joint LNO-NDC meeting. Rogelio shows a draft commissioning plan that he received as basis for discussion and request for feedback from Joerg Wenninger. OMC (optics measurement and correction) is foreseen to start on the 27 March at injection, on 28/3 with first checks  at top energy and further shifts after orbit setup at the beginning of April.  Commissioning of the 90 m optics is planned over easter.
Tobias asks about ion run commissioning. This is not yet scheduled in the commissioning since details like the beta* evolution during the ramp are not yet finalized.
Riccardo introduces the new student Yannis Angelis who will work on HL-LHC optics for RUN4.

MAD-NG parametric matching to cancel 2Qx-2Qy and 4Qx resonances at LHC injection, Laurent, slides

In follow up of the section meeting on the 1st of February with a presentation on emittance growth at injection by Konstantinos Paraschou, Laurent studied how to reduce the main relevant RDTs (resonance driving terms) f4000, f2002 (4Qx and 2Qx − 2Qy) in the LHC injection optics using parametric matching possible with MAD-NG. The parametric maps were already presented for reducing the coupling in LHC, and the parametric normal forms with anharmonicities were presented for reducing Q', Q'', Q''' in FCC-ee (links to further information and scripts used on slide 16). But it is the first time that parametric normal forms with generating functions are presented and Laurent shows the details of the process in his slides. In the matching he varies trim quad (QT) and octupole (MO) strengths and modifies local phase advances, keeping the overall tunes and amplitude detunings of the initial optics constant. He obtains good convergence with 12 iterations for beam 1 and 19 iterations for beam 2. Laurent says that a single iteration of the match command takes only 20 seconds with MAD-NG on this laptop, compared to 10.5 hours with MADX-PTC.

Rogelio had a first look at the newly proposed optimized injection optics and confirmed that the RDTs of interest have been significantly reduced. The local changes in phase advance and the beta beat induced remain small.

Stephane observes that the matching has more degrees of freedom than constraints and comments that the QT strength changes are not so small. He also stresses the need for knobs and would like confirmation that the proposed changes are actually needed and justify changes in the injection optics.

Laurent says that in fact the job is mostly done by the QTs and less by MOs and that he plans to look into introducing further constraints to minimize correction strengths.

 

Update: Soon after the meeting, Laurent extended the script to match RDTs at IP1 and IP5 with new results. Removing the MQT from the matching works fine (with faster convergence) but the final average strength of the MOs is too dangerous (few are around 200A) for injection optics. Keeping the MQTs in the matching and adding tighter constraints on their strengths allows balancing the use of the two magnet families. Other possibilities are the assignments of stronger weights to MOs constraints or to add knobs for each RDT using deferred expressions to specialize the use of the MOs per arc, as suggested by Stephane.

 

Velo aperture, Bjorn Lindstrom, slides

A bulging of the RF-foils in the LHCb Velo region was found in the YETS, reducing the aperture from 49 mm to 38.5 mm in the open Velo position.

Bjorn has performed aperture studies at injection with this bulging. He shows the assumptions and conservative tolerances including an overall 8.5 mm mechanical and alignment tolerance that he used in this study and concludes that the aperture is reduced but should still be ok at injection. He proposes that this should be confirmed by aperture measurements in the Velo region in the commissioning.

Victor Coco from LHCb says hat the beam position in the Velo is well known and rather stable. The Velo is adjusted to the actual beam positions, basically reducing effective alignment uncertainties to the mm level.The measured shift of the collision point is about 1.4mm and they suggest to take this as uncertainty. In addition, they have an uncertainty of the bulging amplitude of about 1mm. The 8.5mm figure could realistically be reduced to 5.5mm.

Eric Thomas from LHCb comments that the foil deformation is not so well known, that the values assumed should be conservative and that more information should become available soon.

Eric and Victor confirm that LHCb will take date in the usual LHC running conditions during at least most of the physics run this year.

Stefano asks if it would be possible to move the Velo further out than the present parking position in the (unlikely) case that things turn out to be worse. Victor thinks there little extra room but will check this points with the relevant LHCb experts.

Bjorn, Stefano and Riccardo remind that tolerances are also required to accommodate beta-beat and injection oscillations and should in fact be conservative. Injection oscillations and failures will also be studied by the injection team (Chiara Bracco et al.). LHCb had already a first feedback from Chiara and will forward the information to the collimation team.

Pascal comments that the aperture measurements at injection will be done with pilots and will induce local losses of some 10^8 (upper limit 10^9) protons in the Velo region. Victor will check that this is tolerable for LHCb.


 

There are minutes attached to this event. Show them.