12 T and 14+T, Dipole Magnets

→ Europe/Zurich
927/1-B23 (CERN)

927/1-B23

CERN

35
Show room on map

Minutes of the meeting Nb3Sn technology

26.04.2023

 

 

Meeting on 14+T program – List of actions at the end of the minutes.

 

Introduction (A. Devred)

The Nb3Sn technology meetings are done to have an open and free discussions about technical issues. They should be carried out in a systematic manner.

The HFM program looks very far ahead. We need to have reasonable and well-established deliverables, but the schedule is not tight. Through HFM we have the means to explore critical missing technologies, data, or parts.

We need to define what we really want to do, what is missing, when and who will carry out the work. 

Strands and cables, current situation (T. Boutboul)

The slides of the presentation are in the indigo link. Thierry presented the situation of the available strands. Both the one-mm-diameter and the 1.1-mm-diameter strands shows instabilities at relative low field and high current density. The limitation around 10-11 T is particularly evident for the FalconD case.

The number of tested samples is quite low. There is the need of more statistic, and the work is continuing.

During the long discussions that followed the presentation the following points were underlined:

  • There is the need to check the load line of the magnets under design. (Action)
  • We need to write down a criterium for stability. (Action)
  • The path to arrive to the choice of the 14+T strand was discussed.
    • Check more samples, concentrate on wires that seems a good candidate for 14+T.
    • Characterize what is available and optimize the chosen strand.
    • With the timescale we aim to we need to choose a strand for the demonstrators and work in parallel to optimize wires for the future. We need to start from somewhere, go step by step, and revisit parameters.
  • We need to align the measurements, in particular within the collaboration with Geneva university. (Action).

In summary we will use the existing strands to start with a demonstrator and prepare the purchase of the next butch of superconductor. This work will be carried out in two phases:

  • Phase one: no other choice of the wires we have. Complete the characterization, communicate to collaborations, and adapt our design of a demonstrator. (Action)
  • Phase two: prepare the next step (from Autumn) using what we learned from phase one measurements. Optimization of Jc, magnet design, Cu/SC ratio, etc. (Action)

 

SMC – RMM programs – next steps (J.-C. Perez)

The second generation of the SMC coils using 11 T strands was manufactured mainly to test different resin impregnations (6 coils). So far (two coils tested) the performance of this generation shows erratic behavior, and the longitudinal load seems not to change much the performances.  To understand and improve the situation the next steps foreseen are:

  • Conductor test in Fresca (Action). In general, every type of conductor will be systematically tested.
  • Re-test of 101 and 102 with tapered shim on the lateral side.
  • Test the 103 b with larger transverse pre-load.

Now, there are still 5-unit lengths of 11 T cable insulated. One unit will be used to wind the 106 coil in collaboration with Ciemat. The use of the other units is not decided for the time being.

Then it is foreseen to use a cable with 0.85-mm strand for a possible, new generation of SMCs.

 

For a new version of RMM it is foreseen to increase by 75-100 micron per side the lateral shim of eRMC coils. A Fuji test is planned to assess this option before implementing it.

 

List of actions

  1. Check the load line of the magnets under design.  All concerned project engineers.
  2. Write down a criterium for stability.       E. Todesco, T. Boutboul.
  3. Align the measurements of Geneva University with CERN needs.              T. Boutboul.
  4. Complete the characterization of available strands, communicate to collaborations, and adapt our design of a demonstrator.             All concerned project engineers.
  5. Optimization of Jc, magnet design, Cu/SC ratio, etc for the future magnets.         T. Boutboul.

 

There are minutes attached to this event. Show them.