TWEPP 2017 Topical Workshop on Electronics for Particle Physics

Session

Production, Testing and Reliability

B

12 Sept 2017, 08:30

Thimann I lecture hall (Other Institutes)

Conveners

Production, Testing and Reliability

• Alex Grillo (University of California,Santa Cruz (US))

Production, Testing and Reliability

• Philippe Farthouat (CERN)

42. The Development of Front-End Readout Electronics for ProtoDUNE-SP LAr TPC

Shanshan Gao (Brookhaven National Laboratory)

12/09/2017, 08:30

Production, Testing and Reliability

Oral

As a prototype of DUNE far detector, ProtoDUNE-SP single phase LAr TPC will sit in H4 beam line at CERN to study detector response to particles. It consists of 6 full-size APAs plus 2 CPAs, with total 15,360 TPC readout channels. The front-end readout electronics is comprised of cold electronics and warm interface electronics. The integral design concept of APA, cold electronics, feed-through,...

13. Quality Control Considerations for the Development of the Front End Hybrid Circuits for the CMS Outer Tracker Upgrade

Tomasz Gadek (CERN)

12/09/2017, 08:55

Production, Testing and Reliability

Oral

The upgrade of the CMS Outer Tracker for the HL-LHC requires the design of new double-sensor modules. They contain two high-density front end hybrid circuits, equipped with flip-chip ASICs, passives and mechanical structures. First prototype hybrids in a close-to-final form have been received from three manufacturers. To qualify these hybrids a test setup was built, which emulates future...

48. Functional Tests of 2S Modules for the CMS Phase-2 Tracker Upgrade with a MicroTCA-Based Readout System

Marius Preuten (Rheinisch-Westfaelische Tech. Hoch. (DE))

12/09/2017, 09:20

Production, Testing and Reliability

Oral

First full size 2S module prototypes for the CMS Phase-2 Tracker Upgrade have been assembled. With two sensors with realistic geometries and 16 CBC2 readout chips on two front-end hybrids, the characteristics of these complex objects can be studied.
A microTCA based readout system was developed to test multiple front-end hybrids simultaneously. Therefore the concurrent information of the full...

56. ATLAS ITk Short-Strip Stave Prototypes with 130nm Chipset

Peter Phillips (STFC - Rutherford Appleton Lab. (GB))

13/09/2017, 08:30

Production, Testing and Reliability

Oral

The ATLAS ITk is working to deliver a new Inner Tracking detector for use at HL-LHC. The strip tracker community has recently constructed partially loaded, double sided demonstrator staves using the HCC / ABC130 chipset in 130nm CMOS technology. Mindful of the need to maximise power efficiency whilst minimising the cost and material of associated cable plant, the system design includes the...

132. A Compact Size, 64-Channel, 80 MSPS, 14-Bit Dynamic Range ADC Module for the PANDA Electromagnetic Calorimeter

Pawel Marciniewski (Uppsala University)

13/09/2017, 08:55

Production, Testing and Reliability

Oral

A compact-size, 64-channel, 80 MSPS, 14-bit dynamic range ADC module for the scintillating electromagnetic calorimeter of PANDA was developed, tested in various detector readout set-ups and are currently in mass production phase. The module performs signal filtration, extract important signal parameters and allow for resolving and parametrizing overlapping pulses. Processed data are pushed to...

97. A Combined Versatile Platform for Silicon Strip Hybrids Reliability Assessment

Evangelos Gkougkousis (Conseil Europeen Recherche Nucl. (CERN)-Unknown-Unknown)

13/09/2017, 09:20

Production, Testing and Reliability

Oral

A unified platform combining a low noise 64-channel power supply with environmental monitoring and a high data rate transmission system, rated up to 1.2 Gbps/sec, has been developed for commissioning of the ATLAS ITk silicon strip hybrids. The power supply with 10mV peak-to-peak noise, implements 3kV isolation and software control. Humidity, temperature, voltage and current are monitored for...