Conveners
Mon-Mo-Po1.10 - Levitation and Magnetic Bearings II
- Mochimitsu Komori (Kyushu Institute of Technology)
- Guangtong Ma (Southwest Jiaotong University)
-
Mengyao Wu (Jiangsu University)23/09/2019, 09:15Poster Presentation
Comparing with traditional bearings, magnetic bearings have the advantages of no friction, no lubrication, high speed, high precision, long life, etc.. Therefore, magnetic bearings have broad application prospects in the fields of flywheel energy storage, wind-generated electricity, high-speed machine tool and so on. The six-pole hybrid magnetic bearing is driven by a three-phase inverter,...
Go to contribution page -
Prof. Guomin Zhang (Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering,Chinese Academy of Sciences)23/09/2019, 09:15Poster Presentation
It is crucial to calculate the levitation force in the designation of superconducting magnetic bearing (SMB). Due to the external disturbances or the time-variable load, it is necessary to study the dynamic levitation behavior in order to ensure the stable levitation of SMB. In this paper, we investigate the dynamic behaviors of the axial levitation force for the radial-type SMB. By adopting...
Go to contribution page -
Kazuhito YAMAGISHI (Yokohama National University)23/09/2019, 09:15Poster Presentation
We are studying magnetic bearings combining multiple cubic superconducting bulks. Calculate the placement by optimum calculation so that the fluctuation of the trapped magnetic flux distribution is minimized according to the cubic bulk arrangement and decide the optimum arrangement for the magnetic bearing.
Go to contribution page
In this experiment, eight magnetic cubic blocks were arranged in a square to... -
Prof. Mochimitsu Komori (Kyushu Institute of Technology)23/09/2019, 09:15Poster Presentation
.
Go to contribution page
INTRODUCTION
Recently, magnetic levitation techniques have been developed for various fields such as energy storage flywheels and magnetically levitated vehicles. Thus, there are many reports about levitation techniques using high critical temperature (Tc) superconducting magnetic bearings (SMBs) composed of superconducting (SC) bulk and permanent magnet (PM). In this paper, new SMBs... -
Eui-Jong Park (Chosun University)23/09/2019, 09:15Poster Presentation
Studies on coaxial magnetic gears (CMG) have been actively conducted. CMGs can replace mechanical gears as they can perform noncontact power transfer, thereby minimizing loss and damage from friction.
Go to contribution page
However, the permanent magnet eddy current loss among the electromagnetic field loss of the magnetic gear is pointed out as the biggest problem in the high speed drive. Among other losses, iron... -
Guangtong Ma (Southwest jiaotong University)23/09/2019, 09:15Poster Presentation
A HTS linear synchronous motor (LSM) that uses YBCO-coated conductor as the secondary excitation system and double layer concentrated windings as the primary was recently demonstrated in our laboratory. Two YBCO-coated conductor racetrack coils were wound on a fiberglass frame via the epoxy impregnation technique and injected dc currents to provide a high stationary magnetic field for LSM....
Go to contribution page -
Dr Wei Wu (Shanghai Jiao Tong University)23/09/2019, 09:15Poster Presentation
Recently non-insulation (NI) HTS coils using coated conductors (CCs) draw extensive attention because of their self-protecting capability. Closed-loop coils are also promising in the application of electrodynamic-suspension (EDS) Maglev train with superconducting magnets since the heat load of the on-board magnet can be significantly reduced, typically >50%. Therefore, closed-loop NI-HTS coils...
Go to contribution page -
Mr Chaoqun Zhao (Tianjin University)23/09/2019, 09:15Poster Presentation
Recently, we investigated High Temperature Superconductor (HTS)-ElectroMagnet (EM) interaction characteristics with experiments and computer simulations. In this investigation, new type of EMs with different geometries were designed and built for comparative analysis. We also set up a three dimensional force measurement system to evaluate the levitation and guidance forces with different EM...
Go to contribution page -
Prof. Xian-Feng Zhao (Lanzhou Jiaotong University)23/09/2019, 09:15Poster Presentation
In this paper we present a quadratic approximation method for the limit value of magnetic stiffness in a high temperature superconducting levitation system. The levitation configuration discussed is that of a cylindrical permanent magnet (PM) placed above a coaxial high temperature superconductor (HTS). The magnetic levitation force between the PM and the HTS is obtained on the basis of Kim’s...
Go to contribution page -
Ms Wei Hong23/09/2019, 09:15Poster Presentation
A new type of electromagnetic guideway for high temperature superconducting maglev was proposed in this paper. The guideway unit is a fan shaped electromagnet that can generate magnetic field for providing enough levitation and guidance forces. A simple multi-object optimization method was used in order to determine the relative optimal geometrical parameters, so that the electromagnet can...
Go to contribution page -
Dr Jie Sheng (Shanghai Jiao Tong University)23/09/2019, 09:15Poster Presentation
Superconducting permanent magnet such as bulk, stack tapes and ring-shape magnet has been proved to be a potential candidate for superconducting motors. In real applications, especially the superconducting electrodynamic-suspension(EDS) levitation system, vibrations in all directions during high speed operation are unavoidable. This paper focuses on the demagnetization process of...
Go to contribution page