# 10th International Conference on Radiation Effects on Semiconductor Materials, Detectors and Devices

Europe/Zurich
Firenze, Italy

#### Firenze, Italy

Dipartimento di Fisica ed Astronomia Universita' di Firenze Largo E. Fermi 2, Firenze, Italy
,
Description

The Conference will cover state-of-the-art scientific and technological advances on  semiconductor-based radiation detector systems and associated electronics, both from the point of view of basic-science research and for application in bio-medical, material science, high energy physics and astrophysics  fields.  The program consists of plenary and poster sessions.

As for previous editions, after a peer-review process, proceedings of the Conference will be published on a special issue of the Journal Nuclear Instruments and Methods in Physics Research  A.

Participants
• Alessandro Gabrielli
• Andrea Gaudiello
• Andreas Nürnberg
• Arie Ruzin
• Carlo Civinini
• Chenhui Wang
• Cinzia Talamonti
• Dario Bisello
• Elena Verbitskaya
• Emanuele Cavallaro
• Francesca Bisello
• Francesca Cenna
• Francesco Guescini
• Gabriele Chiodini
• Gian-Franco Dalla Betta
• Giuseppe Battistoni
• Harris Kagan
• Heinz Pernegger
• Ievgen Korol
• Ivan Lopez Paz
• Joern Lange
• Kerry Parker
• Kurt Rinnert
• Laura Jeanty
• Leonello Servoli
• Leonid Makarenko
• LILI DING
• Lodovico Ratti
• Mara Bruzzi
• Marco Meschini
• Monica Scaringella
• Nicolo Cartiglia
• Pablo Cirrone
• Paolo Morettini
• Riccardo Mori
• Roberto Mendicino
• Sally Seidel
• Sebastian White
• Shuhuan Liu
• Silvio Sciortino
• Sonia Fernandez Perez
• Stefano Lagomarsino
• Sven Wonsak
• Timo Hannu Tapani Peltola
• Tomasz Hemperek
• Tzveta Apostolova
• Vytautas Rumbauskas
• Zheng Li
Support
• Wednesday, October 8
• Conference Registration
• Conference Welcome
• Opening Session
• 1
Invited Lecture: The PixFEL project: developing a fine pitch, fast 2D X-ray imager for the next generation X-FELs
The work will provide a detailed description of the PixFEL project, aiming at the development of advanced instrumentation for 2D X-ray imaging at the next generation X-ray free electron laser facilities.
Speaker: Lodovico Ratti (University of Pavia)
• 2
Invited Lecture: Lessons learned in constructing diamond-based pixel systems
With the first three years of the LHC running complete, ATLAS and CMS are planning to upgrade their innermost tracking layers with more radiation hard technologies. Chemical Vapor Deposition (CVD) diamond is one such technology. CVD diamond has been used extensively in beam condition monitors as the innermost detectors in the highest radiation areas of BaBar, Belle, CDF and all LHC experiments. More recently the first diamond-based hybrid pixel detector system using polycrystalline CVD diamond with state-of-art front-end electronics, the ATLAS FE-I4 pixel chip, was built and installed into ATLAS. This talk will describe the lessons learned in constructing diamond-based pixel systems in high energy physics, specifically the ATLAS Diamond Beam Monitor (DBM).
Speaker: Harris Kagan (Ohio State University)
• 11:00 AM
Coffee Break
• Diamond Detectors
• 3
Diamond detector time resolution for large angle tracks
The physicists working at CERN, in particularly with the LHC high-luminosity upgrade plans, showed great interest in the diamond detector technology in recent years. The applications which have stimulated greater interest are the ones connected to the use of the detector close to particle beams, therefore in an environment with high radiation level (beam monitor, luminosity measurement, detection of primary and secondary-interaction vertices). Our aims is to extend the studies performed so far by developing the technical advances which are needed to prove the competitiveness of this technology in terms of time resolution, with respect to more usual ones, such as Cherenkov radiator coupled to a MultiChannelPlate, which does not guarantee the required performances and working stability in the presence of high integrated radiation doses.
Speaker: Gabriele Chiodini (INFN Lecce)
• 4
Charge collection efficiency of three-dimensional polycrystalline diamond detectors
Three-dimensional (3D) diamond detectors fabricated on high quality single-crystal CVD (scCVD) material show remarkable properties as 100% charge collection efficiency at electric fields as low as 0.04 V/$\mu$m. However polycrystalline CVD diamond (pCVD) is much more easily available with lower cost and larger areas. Hence the implementation of the 3D detector concept with pCVD diamond is highly desirable. The short inter-electrode distance of 3D detectors should improve the intrinsically lower collection efficiency of polycrystalline material, thus allowing to exploit its relative lower degradation to high radiation fluences with respect to the scCVD one. In this work we report on the fabrication and test of 3D pCVD diamond detectors, with different inter-electrode distances, and we prove that their collection efficiency is equal or higher, depending on geometry, than that obtained with conventional planar detectors fabricated with the same material. Preliminary results are also presented on the irradiation and test of these detectors with 1MeV equivalent neutrons.
Speaker: Dr Stefano Lagomarsino (DDepartment of Physics and INFN of Florence)
• 5
LASER IRRADIATION OF MONOCRYSTALLINE CVD DIAMOND: A QUANTUM-KINETIC MODEL BASED ON BOLTZMANN EQUATION
3D diamond detectors are at present investigated as they offer a superior radiation hardness with respect to planar detectors, promising to be the radiation hardest detector ever. Conductive channels are fabricated in the material by means of induced pulsed laser graphitization. The best characteristics are obtained by employing pulse durations as short as tens of femtoseconds. However a number of issues still remains open at the actual state of the art. The composition of the conductive phase is not well assessed as well as the optimal process parameters necessary to obtain low resistivity material, comparable to that of amorphous graphite, without damaging the diamond lattice. A thorough understanding of the graphitization process is still lacking. A better insight of the physics involved could greatly help to tune the parameters, e.g. pulse width, wavelength, field intensity, etc. to achieve an optimal device. In this work we report on a theoretical simulation of the processes involved in laser irradiation under the experimental condition used to obtain high efficiency 3D detectors on monocrystalline diamond material. A quantum kinetic approach based on the Boltzmann equation is employed to describe the response of diamond material to high excitation laser irradiation during and after the pulse duration. The different processes of excitation and rapid thermalization through electron-electron scattering to the final heat up by electron-phonon coupling are taken into account. The energy exchange between the electrons and phonons are given by a separate equation for the lattice temperature where the rate of energy transfer per unit volume from the electrons to the lattice is defined quantum mechanically. As a result of our calculations the electron energy distribution function, average kinetic energy of the electron system and electron density are obtained as a function of laser intensity, laser photon energy (wavelength) and laser pulse duration. Furthermore we obtain the change of lattice temperature caused by irradiation.. Our calculations are intended as the first step of studying the response of diamond to laser excitation below the laser graphitization threshold, with theoretical predictions that can be validated experimentally with charge collection measurements at different laser intensities.
Speaker: Tzveta Apostolova (Institute for Nuclear Research and Nuclear Energy (INRNE))
• 6
Results from the pilot runs and beam tests of diamond pixel detectors
Speaker: Harris Kagan (Ohio-State University, USA)
• 7
First Results on biased CMOS MAPS-On-DIAMOND devices
K. Kanxheri, A. Morozzi, D. Passeri, Stefano Lagomarsino, Silvio Sciortino, L. Servoli A new type of device, the MAPS-on-Diamond, obtained bonding a thinned Monolithic Active Pixel Sensor (a RAPS03 thinned to 25 micrometers) to a standard 500 micrometer pCVD diamond substrate has been fabricated, allowing a highly segmented readout (10x10 micrometer pixel size) of the signal produced in the diamond substrate. A biasing scheme has been adopted for the device to allow the charge transport inside the diamond without disrupting the CMOS functionalities of the Active Pixel Sensor. The device has then been calibrated with monochromatic X-rays, and tested with charged particles to verify the collection of the signal produced in the diamond substrate as a function of the device bias.
Speakers: Daniele Passeri (INFN Perugia) , Keida Kanxheri (INFN Perugia) , Leonello Servoli (INFN Perugia, Italy)
• 1:00 PM
Lunch
• Materials and Defects Characterisation
• 8
Electronic stimulation of interstitial defect reactions in irradiated p-type silicon
L.F. Makarenko*, S.B. Lastovski**, M. Moll***, I. Pintilie**** *Belarusian State University, Minsk, Belarus **Scientific-Practical Materials Research Centre of NAS of Belarus, Minsk, Belarus ***CERN, Geneva, Switzerland **** National Institute of Materials Physics, Magurele, Romania In silicon, the recombination enhancement of migration has been investigated in detail for aluminum interstitial (Ali) [1] and boron interstitial (Bi) [2]. Much less data are available on carbon interstitial (Ci) [3]. We found that electronic excitation by charge injection influences not only the behavior of single interstitial impurity atoms but also the formation and stability of their complexes with interstitial oxygen. Using forward current injection at room temperature with densities in the range of 15-30 A/cm2 the radiation induced boron-oxygen complex, which is the main compensating center in irradiated Si solar cells, can effectively be eliminated. Additionally, evidence has been obtained on the negative-U properties of the boron-oxygen complex. Forward current injection does not influence on the stability of the carbon-oxygen complex but enhances the transformation from its metastable to its stable atomic configuration during the association of mobile Ci with Oi. Characteristics of these processes have been determined and their effects on radiation damage of silicon diodes are discussed. 1. J. R. Troxell et al., Phys. Rev. B, 19, 5336 (1979). 2. J. R. Troxell, G. D. Watkins Phys. Rev. B. 22, 921 (1980). 3. A. R. Frederickson, et al., J. Appl. Phys., 65, 3272 (1989).
Speaker: Leonid Makarenko (Belarusian University, Minsk)
• 9
On polarization in compensated semiconductors
It is well known that in some detectors the performances deteriorate with the operation time or increasing flux (e.g. CdTe and CdZnTe detectors). This phenomenon is often described by the general term "polarization". The exact mechanism is usually unclear, but it is generally agreed that the effects are caused by a buildup of a space charge in the device. Such space charge decreases the electric field causing a decrease in charge collection efficiency. It may also increase the charge collection time which requires longer shaping times in the electronic circuitry, leading to increased electronic noise (mainly 1/f). The nature of the space charge and the formation mechanisms remain vague. It is well documented that the effect is influenced by the semiconductor properties as well as by contacts. Namely, the polarization can be very pronounced with one metallization, and practically disappear with another (for the same semiconductor sample). In this study finite element calculations were used to assess the impact of imperfect ohmic contacts, and compensating trap properties on the space charge formation and on the macroscopic device behavior. It is shown that low recombination velocity of otherwise ohmic contacts leads to a formation of space charge inside the device, but the space charge density is insufficient to affect the electric field distribution significantly without the presence of compensating levels.
Speaker: Arie Ruzin (Tel Aviv University (IL))
• 10
Processing and characterization of epitaxial grown GaAs radiation detectors
Radiation detectors made of epitaxial GaAs are an alternative for silicon devices for spectroscopy and radiography applications requiring moderate photon energies more than 10 keV. Being basic starting material of optoelectronics industry, the processing technology of GaAs devices is well established. Atomic numbers (Z=31, 33) of GaAs extends the X-ray absorption edge beyond Si (Z=14) detectors. In this contribution we report processing of 130µm thick epitaxial GaAs pixel detectors fabricated on heavily n-type doped GaAs substrates. An undoped epi layer was grown in a horizontal CVPE reactor. In the final phase of epitaxy, a thin p+ layer doped with zinc was grown to complete the p-i-n structure. The detectors and test structures were characterized by Capacitance Voltage (CV)/ Current Voltage (IV), Transient Current Technique (TCT) and Deep Level Transient Spectroscopy (DLTS) measurements. Full depletion voltage (Vfd) of detectors is about 15V and leakage current at Vfd below 10 nA/cm2 . Signal transit time determined by TCT is about 8ns at bias voltage less than electron drift velocity saturation, which occurs at >30V bias. DLTS measurements revealed deep levels in epitaxial layers. TCAD simulations were carried out with appropriate defect model in order to verify the experimental results.
Speaker: Timo Hannu Tapani Peltola (Helsinki Institute of Physics (FI))
• 11
An evidence of strong electron-phonon interaction in the neutron irradiation induced defects in silicon
J.Vaitkus, V.Rumbauskas, G.Mockevicius, E.Zasinas, A.Mekys Dept. of New Materials Research and Measurement Technology, Institute of Applied Research Vilnius University, Sauletekio al. 9-III, Vilnius LT-10222, Lithuania It is known an investigation of photoconductivity dependence on excitation photon energy can be used for the deep level spectrum analyze, but an accurracy depends on model that is chosen for the analyze. In this work the temperature dependence of photoresponse spectrum was investigated in the silicon single crystal samples irradiated by neutrons to fluence up to 3e16 cm-2. Due to a rather long photoresponse time constant a new differential photoresponse spectrum analyze method was used for the deep levels near to the valence band energy measurement. The slow transient dependence of photoresponse during the excitation and during decay, and it dependence on additional excitation permitted to propose the deep level competition processes and a role of cascade type excitation of free carriers. Slow relaxation processes also were observed during measurement of galvanomagnetic effects that was analyzed in terms of modulation of conductivity band bottom by clusters. The modeling of bias voltage influence on the contribution of the cluter related potential modulation demonstrated a possibility to avoid this effect at high bias.
Speaker: Vytautas RUMBAUSKAS (Vilnius University, Lithuania)
• 3:50 PM
Coffee break
• 12
Invited Talk: Silicon Sensors for Trackers at High-Luminosity Environment - RD50 Collaboration Status Report
Position sensitive silicon detectors are largely employed in the tracking systems of High Energy Physics experiments due to their outstanding performance. They are currently installed in the vertex and tracking part of the ALICE, ATLAS, CMS and LHCb experiments at LHC, the world’s largest particle physics accelerator at Centre for European Nuclear Research (CERN), Geneva. An upgrade of LHC accelerator is already planned, namely the high luminosity (HL) phase of the LHC (HL-LHC foreseen for 2023). This will enable the use of maximal physics potential of the machine. At the high integrated luminosity of 3000 fb$^{-1}$ the tracking system at HL-LHC will face more intense radiation environment than the present system was designed for. This requires the upgrade of the all-silicon central trackers that will be equipped with higher granularity as well as radiation hard sensors, which can withstand higher radiation levels and higher occupancies also in the innermost layers closest to the interaction point. In order to address the problems caused by intense radiation environment, extensive measurements and simulations studies requirements have been initiated within the RD50 Collaboration, with an open cooperation across experimental boundaries, for investigating different designs and materials options for silicon sensors with sufficient radiation tolerance. Research topics include studies of sensors with n-electrode readout (mainly sensors with p-bulk), which offer the advantage of collecting electrons instead of holes resulting in an improvement of radiation tolerance. Also a further enhancement of performance is investigated in thinned bulk sensors (reduced trapping probability) and in active edge technology (maximized sensitive area). Another line of activity is the development of advanced sensor types like 3D detectors and Low Gain Amplification Detectors (LGAD) designed for the extreme radiation environment at the inner layers. TCAD simulations of silicon strip sensors have expanded to cover both bulk and surface properties after irradiation at HL-LHC levels, producing results that are converging with measurements.
Speaker: Timo Hannu Tapani Peltola (Helsinki Institute of Physics (FI))
• 13
Leakage Current Measurements of highly irradiated Silicon Strip Sensors
The leakage current of irradiated silicon sensors depends, among others, on sensor temperature and irradiation fluence. The temperature dependence is parameterized with the activation energy E$_g$ and the fluence dependence with the current related damage rate $\alpha$. The literature values for E$_g$ and $\alpha$ are obtained from previous measurements, but $\alpha$ is only measured directly to a dose up to 1e15 1MeV neq/cm$^2$ (neq/cm$^2$). Miniature micro-strip sensors ($\sim1\times1$cm$^2$) were irradiated with protons to fluences from 1e12 to 1e15 neq/cm$^2$ and with neutrons from 5e15 to 2e16 neq/cm$^2$ to investigate the reverse current at higher fluence. Precise temperature and current measurements of the sensors from Hamamatsu Photonics K.K. (300$\mu$m thick) and Micron Semiconductor Ltd. (143$\mu$m and 108$\mu$m thick) allow the determination of E$_g$ and $\alpha$. The sensors were measured shortly after irradiation and after room temperature annealing. For the devices irradiated to higher fluences the obtained values differ from the literature value of E$_g$ and the expected value from the linear extrapolation of $\alpha$.
Speaker: Sven Wonsak (University of Liverpool (GB))
• 14
Long term charge collection performance of silicon sensors: an investigation on the causes of the recently observed
Speaker: Riccardo Mori (Albert-Ludwigs Universität Freiburg, Freiburg im Breisgau, Germany)
• 15
Charge collection in Si detectors irradiated in-situ at superfluid helium temperature
Speaker: Dr Elena Verbitskaya (Ioffe Physical-Technical Institute, St. Petersburg, Russian Federation)
• Thursday, October 9
• 3D Detectors
• 16
3D Pixels for the AFP Experiment
Silicon tracking detectors for forward physics experiments at the LHC will be located 210m away from the proton-proton interaction point, but only a few millimeters from the proton beam. The proximity to the beam is essential for the physics programs of these experiments (for example, AFP) as it directly increases the sensitivity of the experiment. Thus, there are two critical requirements for silicon pixel detectors. First, the dead region of the sensor has to be minimized. Second, the tracker has to be able to cope with a very inhomogeneous radiation distribution. Results of the characterization and beam test studies of inhomogeneously irradiated and slim-edged 3D pixel sensors produced at CNM-Barcelona and read out by the ATLAS front-end electronics will be presented.
Speaker: Ivan Lopez Paz (Universitat Autònoma de Barcelona (ES))
• 17
Characterization of 3D and planar Si diodes with different neutron converter materials
In the past few years, considering the shortage of $^3He$, many interesting developments in solid-state thermal neutron detectors have been made (see e.g. [1] and references therein). These devices normally consist in PN junctions with high aspect-ratio cavities filled with neutron converter materials. The size of the cavities and the gap in between them are designed as a trade-off between neutron absorption within the converter material and detection of the reaction products within the silicon sensor, so as to maximize the neutron detection efficiency, for which very good values up to ~50% have been reported. Based on our experience with 3D sensors for High Energy Physics experiments, we have started the INFN HYDE (Hybrid Detectors of neutrons) project. As a first step in this activity, we have developed a new 3D sensor structure aimed at easing the deposition of converter materials while ensuring full compatibility with a pixelated read-out chip for neutron imaging applications. A first batch of 3D sensors, fabricated at FBK in 2012, has been extensively characterized. In order to ease the testing without need for bump-bonding, arrays of cavities have been shorted to obtain diode-like devices with only two electrodes. Electrical and functional tests of bare silicon sensors with alpha particles and laser beams have been carried out to gain deep insight into their characteristics. Moreover, functional tests of 3D sensors with coupled with different converter materials have been performed with fast and thermal neutrons. In spite of the non-optimized sensor geometries, encouraging results have been obtained [2]. However, given the device complexity, both in terms of topography and non-uniform charge collection behavior [2], the interpretation of experimental results was not straightforward, making it difficult to estimate the neutron detection efficiency and also to compare the measured data with Geant4 simulations. For this reason, we decided to perform additional tests using planar diodes covered with different converter materials (e.g., $^{10}B$, $^6LiF$, and polysiloxane [2]). Test devices are PIN diodes of 1.71x1.71$mm ^2$ active area and 300 $\mu m$ thickness, with leakage currents of ~10pA and depletion voltage of ~50V. Experimental results have been collected and compared with simulations carried on Geant4 platform. Although the number of impinging neutrons in the experiments was not known exactly, thus preventing to extract the detection efficiency, the agreement between the measured and simulated spectra was good, thus validating the simulation approach that was later used for device optimization. The new sensor geometries to be implemented in the next fabrication batch and selected simulation results will also be presented. References [1] D. McGregor, et al., Journal of Crystal Growth, 379, 99 (2013). [2] R. Mendicino, et al., JINST, 9, C05001 (2014).
Speaker: Mr Roberto Mendicino (University of Trento, Department of Industrial Engineering, Trento, Italy and INFN, TIFPA, Trento, Italy)
• 18
3D simulations of device electrical characteristics of 3D-Trench electrode detector
The square 3D-Trench electrode Si detector structure is simulated using a 3D Silvaco TCAD tool. Electrical characteristics including electrostatic potential, electric field, leakage current, and capacitance have been simulated in detail. It has been found in simulations that both leakage current and the voltage to reach the geometry capacitance (full depletion voltage, Vfd) increase with radiation fluence. The leakage current and full depletion voltage at 1x1016 neq/cm2 are 41.3 μA (volume is 2x106 μm3) and 90 V, respectively. The geometry capacitance is 99 fF for the structure in our study. The full depletion voltage calculated by CV characteristics at different radiation fluences give similar results to those analyzed by the potential and holes concentration profile simulations. In this optimal configuration the full depletion voltage can be up to 7 times less than that of a conventional 3D detector with all column electrodes.
Speaker: Prof. Zheng Li (Xiangtan University)
• 19
Modeling and simulation of charge collection properties for 3D-Trench electrode detector
3D-trench electrode detector with square geometry was simulated in this paper. Charge collection of 3D-trench electrode detector was simulated using the full 3D device simulation. The induced current and collected charge caused by drifting carriers, generated by a minimum ionizing particle (MIP) incident through the detector, have been modeled and calculated. The results indicate that the total collected charge in irradiated detector change with various particle incident positions and radiation fluence. In addition, we have estimated the average total collected charge generated by the MIP at a random incident position of a 3D-trench electrode detector.
Speaker: Zheng Li (Xiangtan University)
• 20
Speaker: Ms Kerry Parker (University of Sheffield)
• 11:00 AM
Coffee Break
• Electronics
• 21
Monolithic active pixel sensor for ionizing radiation using 180nm HV-SOI process
A new type of sensor for ionizing radiation based on Partially Depleted High Voltage SOI technology (PD-SOI) has been developed. Similar to exisiting SOI based monolithic active pixel sensors (MAPS) a buried silicon oxide inter-dielectric (BOX) layer is used to separate the CMOS electronics from the handle wafer which is used as a depleted charge collection layer. However, compared with these SOI MAPS that suffer from radiation damage in the buried oxide (back gate effect) and parasitic coupling through the BOX layer, this technology offers an additional isolation by an non depleted implant between BOX and the active circuitry. This is a special feature of the PD-SOI process. Therefore we see a high potential with this technology to implement fast and radiation hard MAPS. The concept and measurement results from a first prototype are presented.
Speaker: Thomas Hemperek (Physikalisches Institut, University of Bonn, Germany)
• 22
Measurements Results on a 180nm SOI Monolithic Active Pixel Sensor
Silicon-on-insulator (SOI) technologies have been developed for applications which require radiation hardness since many years. However, for its use as particle detector the total ionizing dose response of SOI devices is more complex than bulk silicon devices due to the buried oxide (BOX). A significant influence of radiation damage in the BOX on the transistor characteristics due to the so-called back gate effect has been observed and published in SOI technologies. We have fabricated and tested a new 0.18 um SOI CMOS monolithic pixel sensor using the XFAB process. In contrast to most SOI technologies, this particular technology provides a double well structure, which shields the thin gate oxide transistors from the Buried Oxide (BOX). This in addition with the particular geometry between transistors and BOX makes the technology promising against back gate effects mentioned before. The process further allows the use of high voltages (up to 200V), which are used to partially deplete the substrate. Thus the newly fabricated device in the XFAB process is especially interesting for applications in extremely high radiation environments, such as LHC experiments. We have carried out a validation program of the technology and the fabricated monolithic pixel sensor in a two stages approach. The first targets the characterization of the charge collection in the silicon bulk below the BOX, the second investigates the radiation hardness of the transistor characteristics, with focus on possible influences of the BOX. The mentioned prototype has been irradiated with X-rays up to 700MRad under two different bias conditions. This presentation summarizes the promising results of the total ionizing dose hardness after this extreme dose of various transistor types - both, standard transistors with different geometries and enclosed transistors. The radiation performance is characterized by transistor threshold voltage shifts, leakage current shifts and transconductance shifts. Results obtained under different bias conditions are compared. Leakage current measurements on the monolithic pixel sensors at different temperatures are used to characterize the silicon bulk behavior and will be presented. To verify the function as pixel sensor we have also tested the device using 55Fe source.
Speaker: Sonia Fernandez Perez (CERN)
• 23
Test-beam results on a monolithic pixel sensor in the 0.18um Tower-Jazz technology with high res istivity epitaxial layer
The ALICE experiment at CERN will undergo a major upgrade in the second Long LHC Shutdown in the years 2018-2019; this upgrade includes the full replacement of the Inner Tracking System (ITS), deploying seven layers of Monolithic Active Pixel Sensors (MAPS). For the development of the new ALICE ITS, the Tower-Jazz 180 nm CMOS imaging sensor process has been chosen as it is possible to use full CMOS in the pixel and different starting materials (including high resistivity epitaxial layers). A large test campaign has been carried out on several small prototype chips, designed to optimize the pixel sensor layout and the front-end electronics. Results match the target requirements both in terms of performances and of radiation hardness. Following this development, the first full scale chips have been designed, submitted and are currently under test, with promising results. A telescope composed of 4 planes of Mimosa-28 and 2 planes of Mimosa-18 chips (monolithic pixel sensors both developed in the 0.35 .m AMS process) is under development at the DAFNE Beam Test Facility (BTF) at the INFN Laboratori Nazionali di Frascati (LNF) in Italy. The elescope has been recently used to test a Mimosa-22 chip (a monolithic pixel sensor built in the 0.18 .m TowerJazz process) and we foresee to perform tests on the full scale chips for the ALICE ITS upgrade by the end of this year. In this contribution we will describe the TowerJazz process and show some first measurements of spatial resolution, fake hit rate and detection efficiency of the Mimosa-22 chip obtained at the BTF facility in June with an electron beam of 500 MeV.
Speaker: Serena Mattiazzo (Università di Padova, Italy on behalf of the ALICE Collaboration)
• 24
High Intensity Irradiation Influence on Gain, Noise nad Offset Univormity of a Pixel Detector Readout designed in 130nm CMOS
We present the measurements of offset, noise and gain uniformity of a prototype pixel detector readout ASIC designed in CMOS 130nm. The chip works in a single photon counting mode, consists of 23552 pixels of 75 um pitch and forms a matrix of 184 x 128. A single pixel consists of a charge sensitive preamplifier with a feedback discharge circuit, shaper, trimming DACs and threshold setting blocks, two discriminators and two 14-bit ripple counters. All these elements fit into pixel area of 75 um×75 um. When a multi-thousand pixel matrix is designed, the mismatch between readout channels is one of the design top priorities. Here, the shaper and the threshold trim blocks play critical roles and they are discussed in more detail. We propose several levels of offsets trimming in each pixel individually namely: - trim DAC controlled by 7 bits to tune the IDAC current, - control of tuning range in two different ways: by multiplying the current IDAC by factor n and/or by changing base current in the source followers, - by adding an extra offset at the input. The ASIC was measured for offset, noise and gain uniformity and trimming capability, which will be presented. In order to be used in an experiment or a final X-Ray detector device it was tested for radiation hardness. Two ASICs were placed in the high intensity X-Ray generator for 27 hours and 237 hours respectively. The distance between the X-ray source to the ASIC was 250mm. The X-ray generator with Mo rotating anode target was running at 60kV-300mA. Each chip received of about 3.7k rad each minute per pixel. The offset, noise and gain uniformity was measured each hour.
• 25
Investigation of total ionizing dose effect and displacement damage in 65 nm CMOS transistors exposed to 3 MeV proton
Speakers: Dario Bisello (Universita e INFN (IT)) , Dr LILI DING (INFN, Padova; Department of Information Engineering, Padova University, Italy) , Dr Marta BAGATIN (Department of Information Engineering, Padova University, Italy)
• 1:00 PM
Lunch
• Poster Session
• 26
Study on the Total Ionizing Dose Effects of SiGe HBTs Irradiated with 60Co γ Rays
The characteristic of the dc current gain degradation with dose and current injection level for SiGe HBT during 60Co gamma irradiation are measured and analyzed. Additionally, the typical dc and ac parameters degradation mechanisms are discussed. The experimental results of the dc and ac electronic parameters before and after irradiation are shown to result in the base current Ib, the collector current IC, the dc current gain and the maximum oscillation frequency fmax exhibiting degradation after irradiation. While other electronic parameters including the cutoff frequency fT, the ac current gain |H21| and output capacitance CCBO do not exhibit any significant change compared with those of pre-irradiation.
Speaker: Prof. Zheng Li (Xiangtan University, Xiangtan, Hunan ,411105, China)
• 27
Simulation of Synergistic Effects on Lateral PNP Bipolar Transistors induced by Neutron and Gamma Irradiation
The numerical simulation methods of neutron displacement effects, total dose effects and ionizing/displacement synergistic effects are established in this work. By the use of semiconductor devices simulation software TCAD, numerical simulation of ionizing/displacement synergistic effects on lateral PNP bipolar transistors induced by neutron and gamma irradiation is carried out with the method of changing minority carrier lifetimes, surface recombination velocity and adding charge traps to SiO2 layer. The results indicate that in the lateral PNP bipolar transistors irradiated with gamma rays up to 50 krad(Si) and with neutrons up to 3.0e13 cm^(-2), the total ionizing dose effects can enhance the neutron displacement damages and lead to larger gain degradation.
Speaker: Ms Chenhui Wang (Northwest Institute of Nuclear Technology of China,Xi’an 710024,China)
• 28
• 29
ATLAS Pixel IBL modules construction experience and developments for future upgrade
The first upgrade of the ATLAS Pixel Detector is the Insertable B-Layer (IBL), just installed in May 2014 in the core of ATLAS. Two different silicon sensor technologies, planar n-in-n and 3D, were used, connected with the new generation 130nm IBM CMOS FE-I4 readout chip via solder bump-bonds. Production quality control tests were set up to verify and rate the performance of the modules before integration into staves. An overview of module design and construction, the quality control results and production yield will be discussed, as well as future developments foreseen for future detector upgrades.
Speaker: Andrea Gaudiello (Univerisyt of Genova and INFN)
• 30
Development of a bidimensional dosimeter for IMRT based on polycrystalline diamond
A bidimensional dosimeter consisting of 12x12 pixels on a 2.5x2.5cm2-wide polycrystalline Chemical Vapour Deposited diamond (pCVD) has been manufactured. The prototype has been tested under Intensity Modulated Radiation Therapy (IMRT) fields for a possible application in pre-treatment verifications of cancer treatments. Tests have been performed under a 6 MVRX beam with an IMRT field for breast cancer. Measurements have been taken by shifting the device along the x/y axes to span a total map of 10x8 cm^2. Main results, shown and discussed in this paper, evidence that absorbed doses measured by our pCVD device along IMRT profiles are consistent with both those acquired with a commercial device based on silicon diodes and calculated by the Treatment Planning System (TPS).
Speakers: Margherita Zani (Universita' di Firenze) , Monica Scaringella (University of Firenze, Italy)
• 31
Belarusian HPHT diamonds. Material properties and detector characteristics
N.M. Kazuchits, L.F. Makarenko, M.S. Rusetsky, Ya. I. Latushko Belarusian State University, Independence Ave. 4, 220030, Minsk Synthetic diamond crystals grown by the HPHT (High Pressure High Temperature) technique have impurities, such as nitrogen and metallic catalysts, as well as inclusion and structural defects, which result in variations of optical and electrical properties for crystals obtained by different producers. In Belarus, synthetic diamonds (trademarked as STM Almazot) are manufactured at the Science and Technology Center “Adamas” [1]. The diamond single crystals, conventionally synthesized by the high pressure (4.5–5.0 GPa) and high temperature (1350–1450 °С) gradient technology using the Ni–Fe–C liquid solvent/catalyst carbon metallurgy system, were investigated. Growth was carried out of about 65–70 h. The solvent/catalyst system comprised the 70% Fe and 30% Ni metals in crystal growth cell, respectively. To characterize the diamond crystal, it was sliced to form diamond plates. The sizes of individual diamond plates vary between 4–20 mm2 (area) and 0.2–0.4 mm (thickness). The plates were investigated by different experimental techniques: optical absorption, photo- and cathodoluminescence and ESR methods [2]. It has been found that STM Almazot crystals have strongly nonuniform impurity and defect distributions. To select plates for detector structures, photoconductivity measurements have been used. Electrical contacts have been formed using boron implantation followed by activation annealing in vacuum. Spectrometric, dosimetric and pulse characteristics of test detector structures were studied, as well as the spectral characteristics of photoconductivity in the UV range. It is shown that the dosimeters, pulse radiation detectors and photodetectors for the UV range have high performance characteristics which are comparable with those of the detectors made of natural type IIa diamond. Small local regions with extremely high sensitivity to radiation have been found in the STM Almazot crystals. These regions can be used to fabricate devices for small field dosimetry. 1. www.adamas.by 2. E. Gaubas, et al.. Diamond and Related Materials, 47 (2014): 15-26
Speaker: Leonid Makarenko (Belarusian University, Minsk)
• 32
Primary Experimental Radiation Effects Results of 28 Nanometer Configuration System-on-Chip(Xilinx Zynq-7010 SoC)
The experimental system we established for evaluating the single event effects (SEE) and total ionizing dose effects (TID) of Xilinx MicroZed Zynq-7010 SoC was introduced in the paper. The variation of the output current of the test SoC during 60Co gamma irradiation was measured. The irradiation dose rate was 0.04Gy(Si).s-1. The test SoC output current changing characteristics under the condition of high temperature (70oC) and room temperature annealing after total gamma irradiation dose 1.69kGy(Si) were surveyed and analyzed. Meanwhile, the SEE sensitive electronic circuit elements including (D-Cache, programmable logic(PL),memory, and registers,etc. embedded in the SoC) and several typical external ports, such as DMA, QSPI and GIC, were tested with 239Pu alpha irradiation on SoC. The single event effects of DDRAM was tested by 1060nm laser irradiation on the bakside. The phenomena of SEU, SEFI and MBU happened in different parts induced by alpha or laser irradiation in the test system were observed.
Speaker: Dr Shuhuan Liu (School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an, Shaanxi, 710049,P.R. China)
• 33
Simulation of Single Event Upset in SRAMs Induced by low Energy Proton With Geant4
The architecture of SRAM and single event upset cross section computation approach are presented. Deposited energy and single event upset cross section are analyzed by the simulation of single event upset in different characteristic dimensions SRAMs induced by low energy proton using Monte-Carlo code Geant4. The simulating result shows that the deposited energy will decrease with the increase of incident proton energy, but it will increase with the increase of characteristic dimensions in the 1-5MeV energy range. And the SEU cross section will decrease with the increase of incident proton energy, but it will increase with the decrease of critical charge in the 1-5MeV energy range.
Speaker: Mr yonghong li (xi’an jiaotong university)
• 34
Primary Design and Numerical Simulation Studies on 3D Si SOI Microdosimeter
For evaluating and measuring the absorbed irradiation microdosimetry in radiobiology and other research areas, a primary 3D pixel structure of Si SOI microdosimeter was given in the paper. For optimizing the detector structure in order to reducing detector insensitive area and improving its charge collection efficiency, a primary optimized mircodosimeter with hexagon pixel structure was offered by numerical simulating , comparing and analyzing its electronic characteristics changed with different technology parameters, such as sensitive area, electrode doping depth, electrode width, guard ring doping profile, etc. Besides, the microdosimeter responses to different irradiation alpha particle energies(0.5MeV, 1MeV, 3MeV, 5MeV), particle incident angle, detector bias voltage, irradiation damage including surface state and displacement damage were also simulated and analyzed. The simulation results may offer some valuable reference data for optimized 3D pixel microdosimeter fabrication and applications.
Speaker: Dr Shuhuan Liu (School of Nuclear Science and Technology, Xi’an Jiaotong University, Xi’an, 710049, China)
• 4:10 PM
Coffee break
• 7:30 PM
Conference Dinner

Ristorante L'Ortone
http://www.lortone.it/

• Friday, October 10
• 35
Performance studies for the new CMS outer tracker module concept at HL-LHC based on measurements of charge collection properties in irradiated silicon sensors
In order to increase the discovery potential of the experiments at the Large Hadron Collider, the high-luminosity phase of the LHC (HL-LHC) is expected to deliver a total of 3000 fb^{-1}. The instantaneous luminosity will be increased by a factor of 5 compared to the LHC design luminosity. This results in an intensified radiation level and track density especially in the tracking systems, requiring new radiation hard sensors for the CMS outer tracker. The CMS tracker collaboration initiated a large campaign to evaluate several different silicon base materials and sensor layouts in order to cope with the increasing demands to radiation hardness and track density. The measurements performed on the sensors include electrical characterization and measurements of the charge collection process in the sensor using a beta source, laser and in testbeams. Additionally, the influence of the strong magnetic field present in the CMS tracker volume has been studied. To cope with the increased track density and trigger rates, a new module concept based on the coincidence of hits in two closely stacked sensors is pursued for the new tracker, allowing the use of tracking and transverse momentum information already at the first trigger level. This is needed to keep the overall readout bandwidth at a manageable level. For further data reduction, the next readout chip will implement a binary readout, comparing the signal height to a threshold value directly in the detector. The performance of the new trigger module concept has been studied using a parametrization of the charge drift in the electric and magnetic field in the sensor. From that, the phase-space of efficient operation of the module concept and the binary readout in terms of collected charge and noise has been explored.
Speaker: Andreas Matthias Nurnberg (KIT - Karlsruhe Institute of Technology (DE))
• 36
Operational Experience with the ATLAS Pixel Detector
The ATLAS Pixel Detector is the innermost detector of the ATLAS experiment at the Large Hadron Collider at CERN. During Run-I, the detector provided hermetic coverage with three cylindrical layers and two endcaps with three disk layers each. It consisted of 1744 n+-in-n silicon modules with a total of about 80 million pixels that were individually read out via chips bump-bonded to the silicon substrate. The ATLAS Pixel Detector started to record data since the first LHC collisions and since the beginning of its operation it performed very well. The operational challenges included the maximization of data taking efficiency, dealing with single event upsets, and the recovery of lost modules. The data acquisition techniques also had to adapt to the rapidly changing LHC beam conditions. In order to maximize the physics potential and the quality of the data, online and offline calibrations were performed on a regular basis. The calibrations ensured maximal hit and charge collection efficiency. The position resolution was improved by pixel charge thresholds, gain and various other online calibrations. With increased luminosity delivered by the LHC, radiation damage effects have been observed in the silicon sensors: an increase in leakage current and change of the depletion voltage, in agreement to the predictions. By the end of Run I, 5% of the modules were not operational, most of which have been already recovered during the current shutdown. In this talk the operational challenges of the silicon pixel detector in Run I are presented, and the expectations for the next LHC data taking period in 2015 are discussed.
Speakers: Laura Jeanty (LBL, USA) , Laura Jeanty (Lawrence Berkeley National Lab. (US))
• 37
The Pixel Detector of the ATLAS experiment for the Run2 at the Large Hadron Collider
The Pixel Detector of the ATLAS experiment has shown excellent performance during the whole Run-1 of LHC. Taking advantage of the long showdown, the detector was extracted from the experiment and brought to surface, to equip it with new service quarter panels, to repair modules and to ease installation of the Insertable B-Layer (IBL). IBL is a fourth layer of pixel detectors, and has been installed in May 2014 between the existing Pixel Detector and a new smaller radius beam-pipe at a radial distance of 3.3 cm from the beam axis. The realization of the IBL required the development of several new technologies and solutions in order to overcome the challenges introduced by the extreme environment and working conditions, such as the high radiation levels, the high pixel occupancy and the need of an exceptionally low material budget. Two silicon sensor technologies have been adopted for the IBL modules: planar n-in-n and 3D. Both of these are connected via bump bonding to the new generation 130 nm IBM CMOS FE-I4 front-end read-out chip. Furthermore, the physics performance will be improved through the reduction of pixel size while, targeting for a low material budget, a new mechanical support using lightweight staves and a CO2 based cooling system have been adopted. An overview of the refurbishing of the Pixel Detector and of the IBL project as well as the experience in its construction will be presented, focusing on adopted technologies, module and staves production, qualification of assembly procedure, integration of staves around the beam pipe and commissioning of the detector.
Speaker: Francesco Guescini (Universite de Geneve (CH))
• 38
LHC Phase 2 upgrade of the ATLAS Pixel Detector
From 2024, the HL-LHC will provide unprecedented pp luminosities to ATLAS, resulting in an additional integrated luminosity of around 2500 fb-1 over ten years. This will present a unique opportunity to substantially extend the mass reach in searches for many signatures of new physics, in several cases well into the multi-TeV region, and to significantly extend the study of the properties of the Higgs boson. The increased luminosity and the accumulated radiation damage will render the current Inner Tracker no longer suitable for long term operations. It will need to be replaced with a new all silicon tracker to maintain tracking performance in the high occupancy environment and to cope with the increase of approximately a factor of ten in the total radiation fluence. New technologies are used to ensure that the system can survive this harsh radiation environment and to optimise the material distribution. Present ideas and solutions for the pixel detector will be discussed in this talk.
Speaker: Paolo Morettini (INFN Genova)
• 39
Radiation Damage in the LHCb VELO and its Impact on Operations in LHC Run 2
Speaker: Kurt Rinnert (University of Liverpool (GB))
• 40
Beam Test Characterization of CMS Silicon Pixel Detectors for the Phase-1 Upgrade
The Silicon Pixel Detector forms the innermost part of the CMS tracking system and is critical to track and vertex reconstruction. Being in close proximity to the beam interaction point, it is exposed to the highest radiation damage in the silicon tracker. In order to preserve the tracking performance with the LHC luminosity increase which is foreseen for the next years, the CMS experiment has planned to build a new pixel detector with four barrel layers mounted around a reduced diameter beam pipe, as compared to the present three layer pixel detector in the central region. A new digital version of the front-end readout chip has been designed and tested; it has increased data buffering and readout link speed to maintain high efficiency at increasing occupancy. In addition, it offers lower charge thresholds that will improve the tracking efficiency and position resolution. Single chip modules have been evaluated in the DESY electron test beam in terms of charge collection, noise, tracking efficiency and position resolution before and after irradiation with 26 GeV protons from the CERN Proton Synchroton equivalent to the fluence expected after 500 inverse femtobarn of integrated luminosity in the fourth layer of the pixel tracker. High efficiency and an excellent position resolution have been observed which are well maintained even after the proton irradiation. The results are well described by the CMS pixel detector simulation.
Speaker: Ievgen Korol (Deutsches Elektronen-Synchrotron (DE))
• 11:00 AM
Coffee Break
• Bio-Medical Applications
• 41
Invited talk: Status of the RDH project
Speaker: Giuseppe Battistoni (INFN Milano (IT))
• 42
MULTIDISCIPLINARY APPLICATIONS OF LASER-DRIVEN IONS: RATIONALE AND PRELIMINARY RESULTS OF THE ELIMED NETWORK
GA Pablo Cirrone1, Giacomo Cuttone1, Georg Korn2, Daniele Margarone2, Francesco Romano1, Valentina Scuderi1,2, Marco Borghesi3, Giacomo Candiano1, Domenico Doria3, Dario Giove4, Tiziana Licciardello1, Mario Maggiore5, Lorenzo Manti6,7, Valentina Marchese1, Giuliana Milluzzo1, Agatino Musumarra8, Francesca Perozziello6,7, Francesco Schillaci1, Antonella Tramontana1 1 Istituto Nazionale di Fisica Nucleare, Laboratori Nazionali del Sud, Via Santa Sofia 62, Catania, Italy, pablo.cirrone@lns.infn.it 2 Institute of Physics of the ASCR, v.v.i. (FZU), ELI-Beamlines project, Na Slovance 2, Prague, Czech Republic 3 Centre for Plasma Physics, Queen’s University Belfast, BT7 1NN, UK 5 Istituto Nazionale di Fisica Nucleare, Laboratori Nazionali di Legnaro, Viale dell'Università 2, Legnaro (Pd), Italy 6 INFN Sezione di Napoli, Complesso Universitario M. S. Angelo, Via Cintia - 80133 Napoli, Italy 7 University of Naples Federico II, Complesso Universitario M. S. Angelo, Via Cintia - 80133 Napoli, Italy 8 Università di Catania, Dipartimento di Fisica e Astronomia, Via S. Sofia 64, Catania, Italy Introduction: Nowadays, laser-accelerated ions represent a fascinating alternative in the field of non-conventional acceleration techniques. The ELIMED project aims to demonstrate the potential medical applicability of optically accelerated proton beams. Design, development and characterization of beam transport, selection and dosimetric devices for high-energy laser-driven proton beams will be presented. Summary: Over the last decades, charged particle acceleration using ultra-intense and ultra-short laser pulses has been one of the most attractive topics in the relativistic laser-plasma interaction research. One of the most challenging ideas driving recent activities consists on using high power lasersto generate high-energy ions for medical applications. The high interest of the scientific community in laser driven ion schemes stems from the fact that conventional ion accelerators, beam transport lines and gantry systems are complex and expensive. More compact laser-based accelerators could significantly increase the future availability of high-energy ion beams in hospitals, thus providing particle therapy to a broader range of patients. In this framework, the purpose of the ELIMED [1] network consists in demonstrating that laser-driven high-energy proton beams can be used for multidisciplinary applications and in particular in the hadron-therapy field. Indeed, the kick-off for medical applications and for radiobiological investigations will be given once the laser-accelerated proton beam transport, selection and dosimetry system is tested and fully operational. We started to design and develop a beam transport line prototype able to deliver laser-generated proton beams with optimized properties and adequate repetition rates. A focusing device consisting of four magnetic quadrupoles is currently under construction. The scope of this device will be to reduce the initial angular divergence of the particle beam accelerated from the target improving the transmission efficiency of the entire transport system. A prototype of the key component of the whole beam line, the Energy Selector System (ESS), able to control and select the laser-driven proton beams, has already been developed and experimentally characterized with mono-energetic proton beams at the LNS-INFN, Catania and LNL-INFN Legnaro, Italy, as well as laser-driven proton beams available at the TARANIS laser facility, Queen’s University of Belfast (UK). Moreover, a Faraday cup prototype optimized for absolute dosimetry with high dose rates and intense ion beams has been designed and tests are ongoing. In this contribution, a description of the solution studied for the beam transport selection and dosimetry, as well as preliminary results obtained with the ESS along with the Geant4 Monte Carlo simulation of such device, will be presented and discussed. References: 1.D. Margarone, G.A.P. Cirrone, G.Cuttone and G. Korn AIP Conf. Proc. 1546, pp. 1-1 doi:http://dx.doi.org/10.1063/1.4816599
Speaker: Pablo Cirrone (Laboratori Nazionali del Sud (INFN))
• 43
Wireless ultra-wide band transmission of bio signals
The main objective of this proposal is to design a system for transmission and reception of signals and biological parameters through dedicated radio circuits using a purely digital approach (asynchronous events). Each source of biomedical parameters will be translated into temporal events that can be transmitted and received without further processing. The system, in fact, thanks to its intrinsic use of events, allows controlling in an extremely efficient release of energy for the transmission of information, and therefore exploit an approach completely on-demand to minimize the consumption of power. The events are generated occurrence of particular patterns in the input signal (and then it is extracted the information content of the signal of interest) and efficiently (with respect to energy consumption, complexity, integration and flexibility) synthesized via a digital system asynchronously. The information is transmitted only when required, allowing for a longer battery life than traditional wireless processes. From the technological point of view it will be exploited the wireless transmission techniques that employs the Impulse Radio Ultra-Wide-Band, localized around 3-5 GHz, for transmitting and receiving signals by very reduced temporal pulses, resulting in very wide spectral occupation. As a consequence of that, we gain limited power consumption at the transmitter side. This wireless system can find various applications in the field of medicine, allowing accurate measurements of various biological parameters detected from time to time by a single receiver (collector). The latter will have the task of reworking the received signals to identify the correct sequence and the source of information.
Speaker: Alessandro Gabrielli (Universita e INFN (IT))
• 44
Development of silicon monolithic arrays for dosimetry in external beam radiotherapy
Francesca Bisello4,5, Marta Bucciolini1,2, Mara Bruzzi1,3, David Menichelli4, Monica Scaringella1,3, Cinzia Talamonti1,2, Margherita Zani1,2 1 University of Florence 2 Azienda Ospedaliera Unversitaria Careggi, Firenze 3 INFN- Florence Division 4 IBA Dosimetry GmbH, Schwarzenbruck, Germany 5 Friedrich-Alexander Universität Erlange-Nürnberg This presentation is a review of the activity of our collaboration, aimed to develop new tools with high spatial resolution and high performances for dosimetry in external beam radiotherapy. The first step (in2007) was the introduction in dosimetry of detector solutions mutated from high energy physics, namely epitaxial silicon as base material, and a guard ring in the diode design. This allowed obtaining state of the art radiation hardness, in term of sensitivity dependence on accumulated dose, with a robust geometry particularly suitable to monolithic arrays and modular design. Following this study a 2D monolithic array has been developed, featuring a detector based on 6.3x6.3cm2 modules with 3mm pixel pitch. This prototype has been widely investigated and turned out to provide good performances in the measure of dose distributions of small and IMRT fields. A further linear array prototype has been recently design to investigate increased spatial resolution (1mm pitch) and technical solutions to further improve radiation hardness. This 24cm long device is based on a modular assembly of 64cm long modules. It features low sensitivity changes versus dose (0.2%/kGy) and dose per pulse (1% in the range 0.1-2.3mGy/pulse, covering applications with flattened and unflattened fields). It has been tested with very satisfactory results in quality assurance of linear accelerators, with special regards to small fields, as well as profiling of proton pencil beams.
Speaker: Francesca Bisello (, IBA Dosimetry, Schwarzenbruck, Germany)
• 45
aSi Electronic Portal Imaging Device for the Radiotherapy In Vivo Dosimetry
Speaker: Angelo Piermattei (Istituto di Fisica e UOC Fisica Sanitaria Università Cattolica S.C. Roma, Italy)
• 1:10 PM
Lunch
• Low Gain Avalanche Detectors
• 46
Invited talk: Low Gain Avalanche Detectors (LGAD) for High Energy Physics experiments
Speaker: Pablo Fernandez Martinez (Instituto de Microelectronica de Barcelona)
• 47
Design and TCAD simulation of double-sided pixelated low gain amplification detectors
A double-sided variant of low gain amplification detector is introduced, suitable for pixel arrays without dead-area in between the different read-out elements. Design options and selected results from TCAD simulations are discussed, along with the proposed fabrication process.
Speaker: Prof. Gian-Franco Dalla Betta (INFN and University of Trento)
• 48
Weightfield: Ultra Fast Silicon Detectors simulator
This presentation reports on the development of *Weightfield*, a simulation program with the aim to evaluate the performance of silicon detectors. The program is controlled by a graphical interface that allows the user to select the type of silicon detector (n-in-n, n-in-p, microstrip, pads), the running conditions (depletion voltage, applied voltage, temperature, magnetic field), the type of incident particle (alpha, ideal MIP, real MIP) and the electronics used to measure the signal. *Weightfield* can also be configured to study the performance of Low Gain Avalanche Detector, as it has a user-configurable gain mechanism. The program predictions have been also validated by laboratory measurements.
Speaker: Mrs Francesca Cenna (Università di Torino e INFN)
• 49
Design of Ultra-Fast Silicon Detectors
In this contribution I will review how Low Gain Avalanche Detectors can be designed and optimized for timing measurements. Specifically I will show how the interplay of gain, signal amplitude, signal rise and collection time, detector capacitance, and read-out electronics determines the UFSDs design and their performances. First results on timing performances of LGAD prototypes manufactured by CNM obtained at test beams at CERN and Frascati will be presented.
Speaker: Nicolo Cartiglia (Universita e INFN (IT))
• 4:00 PM
Coffee break
• Low Gain Avalanche Detectors II
• 50
Radiation effects in RMD Deep-Depleted APDs used as charged particle detectors
Sebastian White, The Rockefeller University, NYC Richard Farrel, RMD/DYNASIL Kirk McDonald and Changuo Lu, Princeton University, NJ Thomas Tsang, BNL Instrumentation Division Mitch Newcomer, U. Pennsylvania Since 2007 we have been developing a high timing precision charged particle detector based on the RMD technology. Our primary focus has been on a solution for high rate applications and hence radiation damage effects have been part of our R&D. The RMD devices have been irradiated in a beam of 72 MeV protons (up to a fluence of 0.5*10^13 n/cm^2. Although QE was degraded and there was an increase in leakage current, as predicted by CMS APD rad dam. scaling laws, performance as a timing detector could be restored to the un-irradiated level by cooling. Recently we have resumed testing at higher fluence in the CERN PS and planning further measurements at FNAL and MGH. We will report on past results and current plans.
Speaker: Prof. Sebastian White (Rockefeller University (US))
• 51
Picosecond timing of high-energy heavy ions with semiconductor detectors
Construction of new accelerating facilities for the investigation of heavy ions requires upgrading of the time-of-flight (TOF) spectrometers for on-line monitoring of the characteristics of ions delivered to experiments. The requested time resolution of the TOF system is in the range of tens of picoseconds, which will cover characterization of ions up to uranium. The TOF systems built on scintillators and microchannel photomultipliers do not satisfy this requirement and, additionally, are not enough radiation hard to withstand the expected fluence of the detected ions and harsh radiation environment outside the beam. Semiconductor detectors and, in particular, silicon detectors whose technology allows device mass-production are now considered as a real candidate for TOF heavy ion spectroscopy. The expected restriction for fast timing of heavy ions with Si detectors is the so-called “plasma” effect related to the dense ion track. This effect creates significant delay in the signal formation, which value can reach several nanoseconds for short-range particles. Obviously, this prevents reaching the picosecond time resolution. Recent results on the timing of high-energy Au ions with Si planar detectors demonstrated the time jitter which is even better than 20 ps. In this presentation the mechanism of charge collection in tracks of heavy ions is examined to explain the observed high time resolution, and the results are projected to the performance of irradiated detectors.
Speaker: Dr Vladimir Eremin (Ioffe Physical-Technical Institute)
• 52
Measurements of LGAD Segmented Devices for high energy physics
The High Luminosity LHC upgrade, foreseen for the third long shutdown of LHC, is pushing the challenge for detectors able to sustain up to a fluence of $2 \cdot 10^{16} \, \mathrm{1 MeV \, n_eq /cm^2 }$. One of the new technologies under development is called Low Gain Avalanche Detectors (LGAD), whose concept is to generate a high electric field region inside the semiconductor material. Charge careers crossing this region may acquire high enough energy to generate secondary ionization initializing a multiplication chain. The higher charge collected by LGAD devices is expected to neutralize the radiation induced signal degradation, moreover it allows to reduce the sensor thickness, and therefore the detector material budget, preserving a good charge to noise ratio. Results of recent production of LGAD sensors from CNM (Centro Nacional de Microelectrónica, Barcelona) will be presented. Both diode TCT studies and electrical characterization of pixel devices will be discussed.
Speaker: Emanuele Cavallaro (Universitat Autònoma de Barcelona (ES))
• 53
Design and Fabrication of an Optimal Peripheral Region for the LGAD
An optimal design of the peripheral region prevents the Low Gain Avalanche Detectors (LGAD) from undesirable malfunctions, which may compromise the accomplishment of their outstanding possibilities as charge particle detectors for High Energy Physics experiments. Without a proper design, LGAD detectors may suffer from premature breakdown or high leakage current levels, which hinder the signal production, as well as enlarging the noise. This work deals with the technological aspects of a suitable LGAD design. The impact of different design strategies for the device periphery is evaluated through simulation. As a result of the conclusions extracted from this work, a new optimized LGAD process has been devise at the IMB-CNM. Details of the new LGAD production are included in this presentation. This work is performed in the framework of the CERN RD-50 collaboration.
Speakers: David Flores Gual (Instituto de Microelectronica de Barcelona) , Pablo Fernandez Martinez (Instituto de Microelectronica de Barcelona)
• Conference Farewell