INFN Milano LHCb UT workshop

from Tuesday 17 May 2016 (14:00) to Thursday 19 May 2016 (16:30)
INFN - Sezione di Milano

        : Sessions
    /     : Talks
        : Breaks
17 May 2016
18 May 2016
19 May 2016
AM
09:00
SALT (until 11:00)
09:00 Tests of SALT8 - Jianchun Wang (Syracuse University (US))  
09:20 SALT Design I - Marek Idzik (AGH University of Science and Technology (PL))  
09:40 SALT Design II - Krzysztof Piotr Swientek (AGH University of Science and Technology (PL))  
10:00 Discussion  
11:30
Flex cables and hybrids (until 13:00)
11:30 Status of flex cable and hybrid projects - Mauro Citterio (Università degli Studi e INFN Milano (IT))  
11:50 Characterisation of second generation flex cables - Nadim Conti (INFN Milano)  
12:10 Plans for production and Q&A test - Mauro Citterio (Università degli Studi e INFN Milano (IT))  
12:30 Discussion  
09:00
Discussion and planning (until 11:00)
09:00 General overview of schedule constraints and milestones for transition to construction & construction - Marina Artuso (Syracuse University (US))  
09:20 Manpower, resources and risk analysis - Sheldon Stone (Syracuse University (US))  
09:40 Communication challenges in geographically fragmented tasks (mostly electronics) and strategies to eliminate “dead times” and interface problems - Olaf Steinkamp (Universitaet Zuerich (CH))  
10:00 Discussion  
11:30
Discussion and planning (until 12:30)
11:30 Discussion  
PM
14:00 Introduction and goals of the workshop - Marina Artuso (Syracuse University (US))  
14:20
Mechanics and peripheral electronics (until 16:00)
14:20 Status of the area from the end of stave to the DCB, based on the model - Jason Emory Andrews (University of Maryland (US))  
14:40 Status and plans for the pigtails - Maria Del Pilar Peco Regales (Max-Planck-Gesellschaft (DE))  
15:00 Mechanics and cooling requirements for the PEPI chassis - Thomas Ernest O'Bannon (University of Maryland (US))  
15:20 Discussions on PEPI assembly and repair - Thomas Ernest O'Bannon (University of Maryland (US)) Burkhard Schmidt (CERN)  
15:40 Discussion  
16:30
Mechanics and cooling (until 18:00)
16:30 Issues on the Mechanics/Electronics Interface - Ray Mountain (Syracuse University (US))  
17:00 Results from Cooling Measurements at Milano - Simone Coelli (Università degli Studi e INFN Milano (IT))  
17:30 Tour of TRACI Cooling Test Setup (Optional) - Simone Coelli (Università degli Studi e INFN Milano (IT))  
14:00
Grounding and shielding (until 15:00)
15:00
Slice Test (until 16:00)
15:00 The UT electronics slice test goals & preparation at Syracuse - Jianchun Wang (Syracuse University (US))  
15:20 COMET & interface test status - Will Parker (University of Maryland (US))  
15:40 Discussion  
16:10
SALT (until 18:25)
16:30 SALT design III - Dr Tomasz Andrzej Fiutowski (AGH University of Science and Technology (PL))  
16:50 Preparation of SALT test setup - Carlos Abellan Beteta (Universitaet Zuerich (CH))  
17:10 SALT chip testing - Tomasz Andrzej Fiutowski (AGH University of Science and Technology (PL))  
17:30 Discussion  
19:30
Social Dinner (until 21:00)
14:00
Visit to laboratories (until 15:30)